 |
Emc2 Fest/CNC Workshop 2007 Time lapse Posted by: samcoinc
Video duration: 406 seconds This is a time lapse video of the emc fest at the cnc workshop. A frame every minute so 600X speed. Have fun :) Related: cnc, emc, emc2, linux, linuxcnc |
 |
4 axis maxnc 10 running through some motions using EMC2 Posted by: samcoinc
Video duration: 103 seconds One of the Emc2 deveolpers is making his max nc into a 5 axis machine. Only one more axis to go. This is using Kinematics within emc to translate actual joint motion into "Cartesian" or "part" motion. Related: emc2, linuxcnc |
 |
EMC2 rigid tapping with tool change Posted by: samcoinc
Video duration: 113 seconds The 2007 cnc workshop/emc2 fest. Limited tooling required some 'creative tooling' drilling the tap hole with a end mill. www.linuxcnc.org Related: emc, emc2, linux, linuxcnc, rigid, tapping |
 |
EMC2 running Hermes engraver making PCB Posted by: samcoinc
Video duration: 58 seconds This is a hermes engraver milling a circuit board using an existing .015 engraving bit. (a bit on the big side) Emc2 is the controller Related: emc, emc2, linuxcnc |
 |
EMC2 closed loop pluto-p (also playing with feedrate override) Posted by: samcoinc
Video duration: 35 seconds This is emc running closed loop using the pluto fpga. The actual rpm is 3600 (600ipm with 2:1 and 3tpi). Encoder is 2540 line so input scale is 60960 (counts per inch) Related: closed, emc2, linuxcnc, loop, pluto |
 |
elbow steam engine Posted by: samcoinc
Video duration: 13 seconds Made in highschool in 1990 or so. sorry about the video quality. Related: elbow, engine, steam |
 |
Emc2 Fest/CNC Workshop 2007 Timelapse Posted by: samcoinc
Video duration: 520 seconds This is a time lapse video of the emc fest at the cnc workshop. A frame every minute so 600X speed. Have fun :) Related: cnc, emc, emc2, linux, linuxcnc |
 |
emc2 dry run of the 3d_chips test program (linuxcnc penguin) Posted by: samcoinc
Video duration: 188 seconds this is using some parker drives to run a hermes engraver. Emc2 is the motion controller Related: emc2, linuxcnc |
 |
EMC2 closed loop test with simple h-bridge and pluto-p Posted by: samcoinc
Video duration: 32 seconds This is emc running closed loop with a simple h-bridge and the pluto-p fpga. The pluto is counting the encoder and outputting pwm-up/pwm-down. The pid loop is closed within the software (emc2) The 'squeek' you hear when I turn the shaft is the cycle by cycle current limit. Related: emc2, linuxcnc |
 |
emc2 running hermes engraver 3 axis Posted by: samcoinc
Video duration: 65 seconds This was thrown togather to see how this would perform as the controller that came with the hermes engraver smoked :). Emc2 seems to run it jus fine :) Related: axis, emc2, linux, linuxcnc |
 |
Servo h-bridge running with emc2 Posted by: samcoinc
Video duration: 30 seconds This is a simple current limited h-bridge driven by emc2. Emc2 is outputting PDM out of the printer port. linuxcnc.org Related: cnc, emc2 |
 |
Maxnc being converted to 5 axis running with EMC2 Posted by: samcoinc
Video duration: 8 seconds One of the emc2 developers has started converting his maxnc mill to 5 axis. He has The B axis mounted and A will be a rotory table on the table (I think the aspec ratio of the video is a little off - sorry) Related: axis, cnc, emc2 |
 |
homing hermes ep module Posted by: samcoinc
Video duration: 63 seconds This shows the homing sequence of the hermes engraver.. Plus jogging around. Related: engraver, hermes |
 |
XYZ liquid dispenser Asymtek Posted by: samcoinc
Video duration: 50 seconds This is a cable driven gantry machine. Run by dos fluidmove software. Related: cnc, dispenser |
 |
hermes 400+ipm with new emc2 doublefreq Posted by: samcoinc
Video duration: 18 seconds This is using emc2 new doublefreq mode. This allows 1 step per base_period instead of 1 step per 2 base_periods. Related: emc2, linuxcnc |
 |
emc2 first rigid tapping Posted by: samcoinc
Video duration: 13 seconds EMC 2007 CNC Workshop. First time Emc2 has rigid tapped. Great work emc2 developers :) Open source machine controller http://www.linuxcnc. org Related: cnc, emc, emc2, linux, linuxcnc, mill, tapping |
 |
EMC2 running hermes 450ipm 50in/s/s doublefreq Posted by: samcoinc
Video duration: 13 seconds This has each axis set to 7.5ips(450ipm). This is running emc2's new doublefreq option allowing for 1 step per base period instead of .5 (1 step per 2 base periods). This is running with a base period of 30us which normall would only allow for a max of 250ipm(4.167ips). My input scale is 4000. Great work emc2 developers. Related: emc, emc2, linuxcnc |
